Monster Truck Invasion

An an action packed card is on tap with SIX Full Throttle Monster Trucks; Relentless, American Outlaw, Stomper, Invader, Hoosier Daddy, and BugZilla competing in qualifying, wheelie, car crushing, and Monster Freestyle! Also we will feature Mud Truck Drags racing in the mud, FMX Motorcross racing, and we cap off the night with a Championship Demo Derby! 

• To purchase tickets, go to our ticket site at: https://florencesp.webtix.co/events/519_June-7th-Monster-Truck-Invasion?cid=FS
• Tickets will be emailed for you to print or to show on a smartphone at the gate. 
• Please see our Frequently Asked Questions page for the event
• All tickets are General Admission. No Reserved Seats.
• No seat marking prior to gate opening.
• No coolers allowed inside the gates. No glass bottles allowed. A full assortment of food, drinks, beer and liquor is available on property.
• Stadium seats/seats with backs are allowed. Seat pads are permitted.
• Note: Event lineup, including trucks appearing, subject to change without notice.
• Times:
  • Gates open: 4 PM
  • Pit Party on the front stretch:4 PM – 5:00 PM
  • Event starts: 5:30 PM
• Admission Prices:
  • Online and on the Day of Event
    • Adult(13 and up): $20
    • Children(4-12): $5
    • Children(3 and under): Free
  • You can print off your FREE Kid’s Admission ticket – HERE
    To use this ticket, show ticket when entering an admission gate with an unused adult ticket. Once an adult ticket has been used to enter, it can no longer be used with a free kid’s ticket.

• Derby Rules – June 7th

  • Derby purse – 1 – $1,500, 2 – $700, 3 – $500, 4 – $250, 5 – $100
    Mad Dog – $500

    No entry fees! Driver pays pit admission at gate, but gets refunded at end of derby.

    2025 Florence speedway bumper swap rules
    1. All judge ’s rulings are final. WE RESERVE THE RIGHT TO INSPECT CARS AT ANY TIME. INCLUDING DRILLING AND SCOPING FRAME RAILS.  
    2. 1980 or newer cars.  Pre ran cars ok. If running a pre ran doesn’t mean you can crease, tuck or weld on anything. We can tell the difference.
    3. YOU CAN CREASE QUARTER PANELS ONLY
    4. Cars must be 100% stock!!! No aftermarket cradles, struts or spindles TIE RODS OR REAR TRAILING ARMS. No cross breeding. Entire drive line must be same as car. (Chevy to Chevy, Ford to Ford). Must be factory engine. Pipes through hood ok.
    5. Drivers door may be welded. All other doors must be chained or wired. No more than 6 places.
    6. Trunks must be chained or wired. No more than 6 places. TRUNKS MUST BE OPEN DURING INSPECTION! No welding or adding metal.  No welding washers for holes.
    7. Hoods may be bolted in 2 places sheet metal to sheet metal. No all thread. May be wired or chained in 4 spots. ¼” chain or 2 strands of wire per hole. It must be sheet metal to sheet metal only ¾” BOLTS MAX. No welding washers for holes. Must be 12” hole in hood in case of fire. Hood must be open for inspection. Remove hood latch.
    8. Must use tires. Must be stock wheels. Any tire ok. NO BARE WHEELS. MUST HAVE RUBBER.
    9. Gas tanks may be moved or left in stock position. Fuel cell preferred but stock tanks ok. Must be secured and does not move. No gas tank protectors.
    10. Battery can be moved to passenger seat. Must be secured and covered. If left in stock location, you can use spray foam around battery. Only 1 battery.
    11. Windshield can be removed. If removed must run 2 windshield bars. One in front of driver other in middle of cowl.
    12. The following must be removed prior to entering fairgrounds. Windows, headlights, tail lights, all chrome and mirrors. Interior must be swept clean of debris and glass.
    13. Stock springs and shocks. No solid suspensions. Spring risers ok, 2 per spring. Wire chains or any weld on rear end spring pockets. Cars must bounce and be stock NOT TIRE BOUNCE, SUSPENSION MUST MOVE. Bottom of bumper heights. Car must sit no higher 21” from ground to bottom of bumper. No lower than 16” from ground to bottom of bumper.
    14. Bar behind seat is highly recommended. 4 point floating cage and rollover bar ok. No bigger than 4” x 4” tubing. Can not be welded to roof. Use gussets off back bar. Back bar can be welded to a 6” plate off B pliar. 4” x 4” max bar.  Gas tank holder off back bar. 3” off sheet metal, 15” from back bar
    15. Car must look and be stock
    16. Paint drivers door in orange or yellow.
    17. Battery may be moved inside of car. 1 battery only. If moved it must be secured and covered. If left in stock you can spray foam around battery.
    18. Bumpers can be welded on including bumper shocks. OEM OR AP ROBINSON OR DEC TYPE
    19. BUMPERS ONLY MUST BOLT TOGERTHER NO WELDING. BUMPER MUST NOT BE NO WIDER THAN FRONT TIRES.  NO POINTY BUMPERS.No Homemade bumpers are allowed. Ends must be open. BUMPER SHOCKS ALLOWED TO BE WELDED 6” ON OUTSIDE  FRAME RAIL. 2”X2” TUBE MAX.
    20. Read rules carefully and follow them! This is a cheap and easy build. Any questions call! There will no starching or bending of rules. NO REFUNDS!!!!!
    21. Once cars are inspected, they will be put in an impound area. No one is allowed to touch car in impound area.
    22. All car numbers must be legible.
    23. 4 each fix plates. 4”x4”x1/4”. Must be 1” in between welds. NO PLATES ON K MEMBER
    24. YOU ONLY HAVE 2 TIMES TO GET THROUGH TECH.
    For questions contact Dave Cook 513-378-5246